Search found 134 matches
- Fri May 11, 2018 9:34 am
- Forum: Technical Talk
- Topic: Turn signals
- Replies: 4
- Views: 9650
Re: Turn signals
The turn signal switch in a '66 is external, driven by a cable. It's very likely that the switch has been knocked out of alignment.
- Wed May 09, 2018 2:15 pm
- Forum: General Talk
- Topic: Hello from Germany!
- Replies: 210
- Views: 894120
- Mon May 07, 2018 5:59 pm
- Forum: General Talk
- Topic: Hello from Germany!
- Replies: 210
- Views: 894120
Re: Hello from Germany!
Fantastic photos! Were you able to remove the A/C / heater box with the fenders on?
- Sun May 06, 2018 6:42 pm
- Forum: Technical Talk
- Topic: EFI - best system?
- Replies: 9
- Views: 19746
Re: EFI - best system?
Toronadotrofeo wrote:I just did fitech efi
I had to do lots of mods like everyone said
Intake linkage and blocked off crossover due the heat I’m very very happy with it
Any performance/mpg changes?
- Fri Apr 06, 2018 10:49 am
- Forum: Technical Talk
- Topic: 1966 Parts List
- Replies: 7
- Views: 18846
Re: 1966 Parts List
Thank you for taking the time to do this. Perhaps it can be turned into a sticky.
- Fri Mar 23, 2018 4:37 pm
- Forum: Technical Talk
- Topic: Transducer for Comfortron Part I
- Replies: 7
- Views: 16487
Re: Transducer for Comfortron Part I
Looks like these guys overhaul comfortron components. I'm going to send them my transducer.
https://originalair.com/restoration-gm-controls
https://originalair.com/restoration-gm-controls
- Tue Feb 20, 2018 5:53 pm
- Forum: Technical Talk
- Topic: Front Hub Bearing Removal
- Replies: 9
- Views: 14580
Re: Front Hub Bearing Removal
I used two 5/16" steel plates to hold the bearing retainer in a press and I was able to press the inner hub out of the bearings.
- Sat Feb 17, 2018 4:31 pm
- Forum: Technical Talk
- Topic: Final drive seals
- Replies: 4
- Views: 8848
Re: Final drive seals
Thank you. Another problem - After resealing my 75ish final drive, I noticed that the driver's side output flange has about 0.040" of side to side play, and about the same in in-out play. I can see the driver's side diff gear moving with it. I have a couple of '66 final drives and that flange i...
- Sat Feb 17, 2018 4:28 pm
- Forum: Technical Talk
- Topic: TH425 manual lever seal
- Replies: 7
- Views: 17032
Re: TH425 manual lever seal
I wish I could help you. I rebuilt my TH425 (and a couple of TH400s) and I never had a problem getting those out. I just don't remember how they are secured, but I bet if you have a closer look it is much easier than it looks.
- Fri Feb 16, 2018 2:56 pm
- Forum: Technical Talk
- Topic: Eldorado brake calipers
- Replies: 28
- Views: 46771
Re: Eldorado brake calipers
Thanks Bruce. We'll see how that goes.
Does anyone know where I can find new boots for the inner tie rod ends for a '66? Mine are very tight, but the boots are in bad shape. It would be nice to save some money and just replace the boots...
Thanks.
Does anyone know where I can find new boots for the inner tie rod ends for a '66? Mine are very tight, but the boots are in bad shape. It would be nice to save some money and just replace the boots...
Thanks.